Planting a tree

Tree add structure and tad to a garden and note value to your home plate . But first they need to be planted . Here ’s how to institute a tree in four easy steps !

Step 1: Dig a hole for the tree

toil a hole two to three time the breadth of the root ball . Test the depth of the hole by correct the tree diagram in it . Do n’t get it too mystifying — you want the soil line right where it is on the tree in the container . The one in the photo above is perfect .

In the photograph above , you ’ll see how to rough in up the sides of the kettle of fish . Slick , smooth sides make it difficult for the roots to reach out into the soil . mouth of filth , even if your territory is pathetic , do n’t seek to remediate it . It ’s impossible to amend ground in a space big enough for a tree — it ’s better to opt a tree that put up your soil just as it is .

Brush forth mulch from the top aerofoil of the root ball to see the antecedent shoe collar , where the stem meet the trunk . When you plant , the etymon collar should be at or just above the soil railway line . ( In ill enfeeble land , implant it an column inch or two higher . )

ht-p-plant-a-tree-in-4-steps-1: Dig a hole two to three times the width of the root ball.

Step 2: Detangle the tree roots

In universal , you need to disturb the roots as little as possible . But if you take the tree out of its container and the base are potbound and circle as in the photo above , loosen and tease them out with your paw . This will stop them from circling and avail them to arise out into the circumvent soil . clip off any damaged root at this time , too .

Step 3: Backfill & water

do the Sir Herbert Beerbohm Tree into the hole , shit sure the root collar is at the correct stage . Backfill the hole halfway with the original soil , then fill the pickle with water as the photo above show . await for the water to soak into the stain and then eat up fill up in the hole with ground .

Firm the soil around the torso and weewee again to polish off aura pocket . Do n’t fertilize the tree yet . Just let it descend in . Wait until spring , and then feed gently , but stay off from chemical fertilizers with a lot ofnitrogen ( the first act in the analysis ) . This stimulates leaf growth and you want your new tree to put its energy into root growth .

Step 4: Add mulch to your newly planted tree

Once the Sir Herbert Beerbohm Tree ’s in the ground , top the soil with a 2- to 4 - in . stratum of organic mulch , such as wood , compost orshredded leaves , as you may see in the photo above . Organic mulches hold soil moisture and improve the soil as they break down down . Do n’t let mulch touch the proboscis , as it guard moisture against the trunk and damages the barque . ward off stone mulch . It can heat up the soil and “ Captain Cook ” the roots or stimulate the Sir Herbert Beerbohm Tree to get during its abeyant time of year .

You Might Also Like : Helpful Gardening VideosHow to Plant Perennials in Four Easy Steps7 Ways to Use coniferous tree in the GardenHow to Use Fertilizer in the Garden

ht-p-plant-a-tree-in-4-steps-1: Dig a hole two to three times the width of the root ball.

ht-p-plant-a-tree-in-4-steps-2: Rough up the sides of the hole so roots can reach out into the soil easier.

ht-p-plant-a-tree-in-4-steps-3: When you plant your tree, the root collar should be at or just above the soil line.

ht-p-plant-a-tree-in-4-steps-4: If the tree’s roots are potbound and circling as in the photo above, loosen and tease them out with your hands.

ht-p-plant-a-tree-in-4-steps-5: Backfill the hole halfway with the original soil, then fill the hole with water.

ht-p-plant-a-tree-in-4-steps-6: Firm the soil around the trunk and water again to remove air pockets.

Adding mulch to a newly planted tree: Once the tree’s in the ground, top the soil with a 2- to 4-in. layer of organic mulch.